Or otherwise if the product(s) is altered or improperly repaired or serviced by anyone other than Honeywell factory service. Seller shall have no obligation under this Limited Warranty Specifications or proves defective in materials or workmanship under normal use and service.
5869 panic button free#
Shall be limited to repairing or replacing, at its option, free of charge for materials or labor, any product(s) which is proved not in compliance with Seller's Original purchase unless the installation instructions or catalog sets forth a shorter period, in which case the shorter period shall apply. Service for 24 months from the date stamp control on the product(s) or, for product(s) not having a manufacturer’s date stamp, for 12 months from date of Product(s) to be in conformance with its own plans and specifications and to be free from defects in materials and workmanship under normal use and Honeywell International Inc., acting through its Security & Custom Electronics business ("Seller") 165 Eileen Way, Syosset, New York 11791, warrants its This device must accept any interference received, including interference that may cause Operation is subject to theįollowing two conditions: (1) This device may not cause harmful interference, and (2) This device complies with Part 15 of the FCC Rules. Weekly) to insure the system's operation at all times. Recommendations must be included for a specific program of frequent testing (at least The user, as well as acquainting the user with the proper operation and limitations of the alarm system and itsĬomponent parts. The installer should assume the responsibility of developing and offering a regular maintenance program to Vital to continuous satisfactory operation of any alarm system. Regular maintenance and inspection (at least annually) by the installer and frequent testing by the user are 5869 Holdup Switch/Transmitter Detailsįigure 2. Re-install screws to secure cover and case as shown inįigure 1. Observing correct polarity, insert the battery into the Remove faulty battery and dispose of properly.
5869 panic button install#
NOTE: Use care not to bend the antenna whileĪttempting to remove or install the battery. Remove the screws securing the 5869 cover and case to Replacing the battery, possibly breaking the Tamper
Exercise caution not to jar the case while Tamper release tab once the cover and mounting screwsĪre removed. IMPORTANT: The case will be held in place by the Dispose of usedīatteries promptly and properly. Do not recharge, disassemble, heat above 100☌, or incinerate. The 5869 is one closed input loop zone (loop 1). Holdup Switch/Transmitter should be treated as "RF" Security System Control Panel Installation and Setupĭuring programming of the control panel, the 5869 Programmed as a 24-hour silent zone type. The 5869 Holdup Switch/Transmitter should be Respective Security System Control Panel Installation and Manufacture used for enrolling the 5869 with the security
5869 panic button serial number#
The 5869 has a permanent serial number assigned during Secure the case with the cover to its mounting location IMPORTANT: To prevent damage to the case, do notĤ. Secure the cover to the case with the two screws (No 6 x 6 x ¾ screw (supplied) at the breakaway tamperģ. Position the case to the desired location and install one Install the battery into the battery holder observingĢ. Mounting location (refer to the Security System Controlġ. Tests to verify adequate transmitter signal strength at desired Refer to the figure and steps thatįollow for typical mounting installation.īefore mounting the 5869 permanently, perform Go/No Go Mount the 5869 under a counter or money drawer for easyĪccess by the cashier. The cover is removed, or when the unit is forcibly removed The 5869Īlso contain tamper switches that are activated either when Reset key K4563 must be used to reset the device. Once the 5869 trigger (Figure 1) is activated, the supplied Panel, which then sends a burglary alarm to the central Transmitter is activated, it sends an RF signal to the control Or money draw for inconspicuous operation. The 5869 is typically mounted under a counter RF transmitting device used for activating a holdup signalĪt the security system control, and/or any other securityĪpplication. The 5869 Holdup Switch/Transmitter is a finger-operated